Datsun 510 Rear Suspension

Part Number:  224-1004
 
Rear Control Arm Bushing Kit: This kit consists of steel bushings and sleeves that replace the old rubber bushings. Spherical bearing type for stock bolt. Also fits 610.
Price: $300.00
Part Number:  224-1005
 
Rear Control Arm Bushing Kit:  This kit consists of steel bushings and sleeves that replace the old rubber bushings. Spherical bearing type for 5/8 bolt. Also fits 610.
Price:$295.00
Part Number:  234-9010
 
Bolt Kit, Rear Control Arm Bushing:  5/8" bolts, nuts, and washers for use with 224-1005 on a fully adjustable rear crossmember.  PL 510 or PL610
Price:$30.40

Part Number:  234-1000

 

Rear Crossmember Solid Mount Kit:            Also fits 610.

 

Price: $65.00

Part Number:  234-1002

 

Rear Diff Solid Mount Kit:  For mustache bar with 2 3/8" OD, fits 510-610-240-280Z.

 

Price: $55.00

Part Number:  234-1009

 

Rear Diff Solid Mount Kit:   For mustache bar with 1.95" OD, fits 510-610.

 

Price: $55.00

Part Number:  234-1826

 

Rear  Lower Control Arm Spring Mount: When use with the rear weight jacker, this kit allows for the use of 2.5" ID coilover springs.  Installation requires cutting the existing spring bucket off of the control arm and welding this in place.

 

Price: $120.00

Part Number:  234-1008

 

Rear Weight Jack Assembly: Allows ride height adjustment at the rear of the car.  Bolt-in installation.  Mounts where the rear seat belt mounting bolt is located.  Allows for the use of 2.5" ID coil over, stock diameter, Roadster,or other diameter springs.  Specify spring I.D. When ordering.  Includes all hardware.

Price: $195.00

Part Number: 826-XXXXX

Coilover Springs: Hyperco 6" Free length 2.50" I.D.  For use with Rear weight jacker kit 

Price: $57.99

 

Part Number:

826-06650: 650 lb/in    826-06700: 700 lb/in    826-06750: 750 lb/in    826-06800: 800 lb/in

NEW

Part Number: 284-2510

 

Rear sway bar kit: Datsun 510, adjustable.  1” diameter tubular sway bar with splined ends, aluminum arms, cowbells, endlinks, and hardware.  Requires welding for installation.

 

Price: $475.00

Part Number:  820-DS702

 

QA1 single adjustable coil over shock: complete with 2" diameter shock body, coil over kit, urethane lower eye bushing, and stud mount top mount. 7" stroke.  Includes spring, specify rate.  

You can easily adjust your compression and rebound valving and get the hard-core performance you need. One knob allows you to choose from 18 valving options that adjust both compression and rebound valving simultaneously, allowing total suspension control in one easy-to-reach location.

  • Simultaneous Compression and Rebound Adjustment

  • Coil-Over

  • Lightweight Aluminum

  • Ride Height Adjustable

  • Spring Mounting Hardware Included

  • 100% Dyno Tested and Serialized

  • Revalveable and Rebuildable by the QA1 Factory or QA1 Authorized Service Centers

  • American Made

  • Precision Machined Aluminum Piston with PTFE Piston Band

  • 5/8” Centerless Ground, Hard Chrome Plated, Solid Piston Rod

  • Three Step Sealing System

Price: $295.00 each

 

Part Number: 210-T114W

Spanner Wrenches: (1) wrench for the spring seat adjuster, (1) wrench for the lock nut on QA1 coil over rear shocks.  Note: These don't work on our threaded collars.

Price: $19.95/set

 
Rear Crossmember shown powder coated and with enlarged exhaust hole.  Both are extra cost

Part Number: 299-1004

Fully Adjustable Rear Crossmember : Relocated pivot points for improved geometry.  Inner bracket is adjustable for camber and toe.  Includes 5/8" bolts, brackets, toe adjusting shims, and inner bracket triangular retainer.  A core crossmember is required.  You can save $100.00 if you cleanly remove all the brackets and cleanup the crossmember prior to sending it to us.

Price:  $565.00

Part Number: 299-1012

Labor to enlarge exhaust hole:  Remove existing tube through crossmember and install a 3.5" diameter tube for increased exhaust tube clearance.

Price:  $100.00

THERE WILL BE A 20% RESTOCKING FEE FOR ALL APPROVED RETURNS, AND THE BUYER IS RESPONSIBLE FOR ALL SHIPPING CHARGES ON SAID  APPROVED RETURNS THERE IS NO STATED OR IMPLIED WARRANTY DUE TO THE UNUSUAL STRESSES PLACED ON RACING/HIGH PERFORMANCE STREET PARTS AND BECAUSE WE HAVE NO CONTROL OVER HOW THEY ARE USED OR INSTALLED.  PRICES ARE SUBJECT TO CHANGE WITHOUT NOTICE.  Click here for additional terms and conditions

Design Products/DPracing

5462 Oceanus Drive Unit E

Huntington Beach, California  92649

(714) 892-1513

E-mail: dpracing.co@gmail.com

 

 

© 2017 by Design Products/DPracing Proudly created with Wix.com